Best plasma cutter under $500

Are you on budget and want to get the best plasma cutter under $500 or less? Are you facing any issue while selecting the cheap plasma cutter? We are here to help you because our team has tested many cheap plasma cutters to check their performance and cutting capabilities.

And the results were unexpected as these cheap cutters worked like expensive plasma cutters, and there was no difference in their performance.

Also, we concluded that to make perfect cuts on the metal, you need practice and mastery in the field, not expensive cutting machines.

After testing many of the plasma cutters, our team has picked the best plasma cutters under $500, which are excellent in performance and have a competitive advantage over other machines.

 Best Plasma Cutter Under $500 2021

 

1-Lotos LTP5000D 50Amp

best plasma cutter under 500

           

             Key Features

  • Dual voltage working
  • 60 percent duty cycle
  • The advanced cooling technology used

Unusual and nonsense plasma cutter under 500 dollars uses non touch Arc technology and an excellent cutting performance on many of the metals where other machines fail at this point.

On the other hand, the 50 amp output working makes it easier to cut 5/8 inches steel, and dual voltage capacity makes the cutter more versatile as it can work on 120v to 240v power.

In addition to this, the machine’s weight is less, which is only 19.40 pounds, which makes it super easy to transport and includes helping tools like moisture separator, air filter, and even pressure regulator, which help to do your work with no time.

PAPST’s advanced technology is used for the cooling of the machine and can be used at the light and thick metal, and due to technologies used, the performance increase at maximum level.

Moreover, a 60 percent duty cycle on 50 amps by running the cutter on 240v makes it more favorable also, one year of warranty gives you peace of mind.

One of the essential things included with the package is a 13-foot torch connection, but on the other hand, the downfall and complaint about this cutter are that the ground connection is only 6 feet and of cheap quality.

Moreover, to save you from any damage, nonhazardous compressed air is used to cut the metals you want and use a comfortable handle to carry and move the machine to different locations.

Lastly, the machine comes ready to use like a pre-installed NPT 1/4″ industry type D plug and air filter regulator. Make sure to easily and quickly connect your air compressor within no time and start working.

Pros
  • High frequency non touch Arc
  • Lightweight and portable
  • Necessary equipment included
  • Versatile and can be used on many of the metals
Cons
  • 120v connector is not included
  • The ground connector is only 6 feet.

2-Forney Easy Weld 251

under 500 plasma cutter

           

             Key Features

  • Drag torch advanced technology
  • 110/120v input capacity
  • 20 amp output

We like Forney Easy Weld 251 20 P Plasma Cutter because it gives exceptional and outstanding results as the manufacturing company promised.

On the other hand, if you want to cut rusted and painted metals, it will miss, but the results will not be as good as other expensive machines.

In addition to this, if your work demand cutting ¼ inches or less, then you will get results like expensive cutters and making significantly less effort, and finish cut edges will be clean.

We have heard complaints about many other plasma cutters under 500 dollars that the torch and ground connector are short in length like in Lotos LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter the ground connector is only 6 feet.

But in Forney Easy Weld 251 20 P Plasma, the torch and ground connectors are according to requirements, and if you want more length, you can buy an extra extension, which is readily available in the market.

The price of the Forney comfortable weld 251 20p is the same as Lotos LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter, but the cutter is a little heavier and also portal able.

The cutter is user-friendly and best for a newbie, which comes with one year of warranty and advanced DRAG TORCH technology.

Also, to increase the life span and make it the durable metal case has been used, making sure to secure the machine’s internal components if it accidentally fell.

We have found one problem with this cutter as there are 110/120 input volts to use the machine on a thin metal plate-like ¼ inches and aluminum of 3/16 inches.

As advisors, we will recommend Forney Easy Weld 251 20 P Plasma Cutter to those who want to do light and thin steel metal cuts.

Pros
  • 35 percent duty cycle
  • Lightweight and portable
  • Can be used on rusted and painted material
  • Perfect torch and ground connector
  • Compact plasma cutter
  • One year of warranty
Cons
  • Low input voltages
  • ¼ inches steel cutting

3-Display4top CUT-50 under $500 cutter

cheap plasma cutter

           

             Key Features

  • Built-in control system
  • 60 percent duty cycle
  • 110v/220v input power

Display4top CUT-50 DC Inverter Plasma Cutter is a cost-effective and energy-saving machine for metalwork, and your shop with a significantly lower price as compared to other top reviewed cutters.

On the other hand, the plasma cutter uses dual voltage input current like 110/220v and provide the proper current to the machine it uses the inverter technical power switch.

 The cutter is easy to understand, and to look at which setting the cutter is working, a large display screen is also available on edge.

The duty cycle on this plasma cutter is 60 percent, which makes the machine’s performance speedy while, on the other hand, consuming very little power.

Due to all these features, the output results are unmatchable while using other traditional cutters, and also Display4top CUT-50 DC Inverter is very fast in speed, so it can save you precious time.

You don’t need to worry about the other safety features like overheat, over-current, and under-current. All these are under control and cannot harm you again for more safety; there is a mask with the package.

Meanwhile, the machine is compact and uses a handle to make it easy to transport to other locations and be used in many industries.

The only complaint we received from this plasma cutter user the assemble is a little complicated but on the other hand ground clamp used in the unit makes your work easy.

Pros
  • Much cheaper as compare to others in this class
  • Inverter power switch
  • Large display to understand
  • Energy saving
Cons
  • Assembly of the cutter is complicated to understand
  • 28.1 pounds weight of the cutter

4-Vipercut 30amp Plasma Cutter

affordable plasma cutter

           

             Key Features

  • Dual input voltage
  • 35 percent duty cycle
  • 30 amp power

One of the best plasma cutters under $500, which is available in small size and portable, can be transported to any project site.

Razorweld is the Vipercut 30amp Plasma Cutter manufacturer, which is very famous for making special plasma cutters at a reasonable price for beginners and hobbyists.

On the other hand, the cutter’s output amp capacity is 30 amps, but it is more powerful can also cut like 50 amp power plasma cutters.

In addition to this recommended cutting capacity of the machine is ¼ inches, but you can also do cutting of ¾ inches in the short run.

Also, to make the cutter more versatile dual voltage input power is used, and also there is a built-in regulator to control the machine’s functionality.

To increase the cutter autopilot Arc system’s performance, it also includes other equipment like a torch and consumable set.

Thirty-five percent duty cycle also increases the performance, and the 9-foot ground clamp is perfect in length for most of the user, which is short in many of the other plasma cutters.

Also, Vipercut 30amp Plasma Cutter is designed in Australia and built-in China, and cutting on thick metal is possible in the short-run, but the cutter gets very slow by doing this process.

Pros
  • Built-in regulator
  • Pilot arc system
  • Inverter power source
  • ¼ inches also ¾ inches cutting capacity
Cons
  • Customer care service is not good

5-ZENY DC Inverter Plasma Cutter 50AMP

           

             Key Features

  • Overheat built-in function
  • 110/220v input power
  • 50 percent energy saving

One recommended best plasma cutter under $500 for DIY work and cutting the metal in different sizes.

On the other hand, the cutter makes sure that there would be no warp on the metal, which usually occurs while using the jigsaw and other traditional methods.

There are many accessories and essential tools like cutting torch, plasma tips, air pressure regulator, grounding clamp, chipping hammer/wire brush, welding face mask, and air pressure reducing valve.

It also includes an easy understanding instruction manual to make you more familiar with this plasma cutter and save you from any wrong installation.

More importantly, the cutter is 50 percent more energy-saving because the technical inverter switch is used to maintain the current.

Also, cooling technology is used to increase the machine’s efficiency by 30 percent, and dual voltage working makes the machine work on lots of metals.

Moreover, the cutter is compact and lightweight, so it can easily be used at different positions and primarily used for DIY jobs and general repairs and maintenance.

Large digital LED is used to adjust the settings quickly and also uses autopilot Arc system, on the other hand, to make sure that the cutter is safe from any damage built-in safety features used.

Pros
  • 30 percent more efficient as compared to other
  • Compact, lightweight, and portable
  • Best for entry-level as no skills required
  • Very cheap in price
Cons
  • Cannot be used on heavy jobs
  • Plug and hose are not included with the package.

6-PrimeWeld 50A Air Inverter Plasma Cutter

user friendly plasma cutter

           

             Key Features

  • 110v/220v working capability
  • Three years of ling warranty
  • Different duty cycles at different voltages

Lastly, we have PrimeWeld 50A Air Inverter Plasma Cutter, which can be used for home jobs and also can be used for construction and heavy industrial jobs.

On the other hand, it uses advanced inverter technologies to make it an exceptional plasma cutter and can be carried to any project site easily.

In addition to this, coming to the cutter’s working capabilities, the machine’s output amp capacity is 50 amps and has a dual input power source like 110v/220v.

Moreover, the cutter is very simple, easy to use, and time-saving because it requires minimal cleaning and maintenance time.

As the cutter is very powerful, you can use it on more thick metal using DC power mode and create significantly less distortion while working.

MOSFET advanced feature gives more power output to the machine to cut thicker metals and steady work for thin metal surfaces.

Different duty cycles like 40%, 50%, and 60% at different voltage increase the performance as you want, and dual voltage capacity makes the machine work on lots of metals as you wish.

Coming to the cutter’s accessories then there are cutting torch, ground clamp, air filler, air hose, and many more.

To cut thin metal, you can run the machine on 120v at standard household power, and for thick metal, 220v is used.

Also, if the cutter’s current flow is not accurate, then there is a sensor that senses the current and automatically adjusts it according to the cutter parameter.

To ensure your safety, compressed air is used, so you don’t need to carry any hazardous gas with you while working in different situations.

Pros
  • 24 pounds weight of the machine
  • Thick and thin cutting ability
  • Compact and lightweight
  • Required less cleaning and maintenance
  • User friendly
  • Includes all the accessories
Cons
  • Thick metal cuttings are not so good.

Buyers Guide

Before buying the best plasma cutter for under $500 or less, you need to look at many of the crucial factors if you are entry-level in this welding field and compare the feature used in different plasma cutters.

Lastly, select the machine which is a top cutting machine and available at a significantly lower price.

Voltage capacity 

Today’s market is full of single voltage and dual voltage plasma cutters. We will recommend a double voltage machine because it provides the cutter more power and more metal cutting facility.

Single voltage cutter works typically on 120v and can be used on light projects and thin metal like doing small work at home and farm and soft, thin metal cutting at your shop and general repairing.

While dual input voltage cutter can work on thick metals and give you the option to do work on lots of metals.

Metals

Different plasma cutters have additional cutting capabilities, like if you want to cut rusted and painted metals

, then try to buy a noncontact cutter while on the other hand, if you are working on new and clean metal, then it does not matter.

Cutting capacity

There are many plasma cutters which can do severance cuts as well as clean cut. Severance cut means to cut on thicker metal, while clean-cut means cuts on thin metal.

Try to get the plasma cutter with both options, but severance cuts are not so good with a plasma cutter while better than a jigsaw.

Safety options

Due to modern technologies, different safety features are used in the plasma cutter like overheat control, over-current and under current management, thermal technologies that make sure to get excellent cuts and also make sure to save the cutter from any damage.

So try to get the cutter with all these features.

Cutter with compressor

There are cutters with the built-in air compressor, while others are available without a compressor, so if you have a compressor, you can get without a compressor cutter.

While on the other hand, if you don’t have an air compressor, try to get the plasma cutter with a built-in air compressor available at an affordable price. It also becomes effortless to carry the cutter to any location.

If you have a separate air compressor, you will have to separately carry a cutter and air compressor, making it difficult to transport.

Frequently asked questions

Is cheap plasma cutter any good?

Many cheap plasma cutters also perform like expensive cutters and available with the same features and settings as costly cutters.

Also, cheap cutters are compact, small in size, and portable, while expensive cutters are more massive than heavy and industrial jobs.

The one difference between cheap and expensive cutters is that cheap cutters are used for light and thin metal, while costly machines are used for commercial and heavy industrial jobs.

What is the difference between cheap and expensive plasma cutters?

There is no more difference between these plasma cutters. There may be little shortage of the features and limited setting options in cheap welders.

Also, the best budget plasma cutter cannot be used for heavy and thick metal cutting jobs in most cases.

Final verdict

Are you looking perfect and unbeatable plasma cutter with fully loaded features and control settings and also want to spend some good money? then we will highly recommend Lotos LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter

If you are looking for a plasma cutter which should be very cheap and can perform extraordinary tasks and also dual voltage, the ZENY DC Inverter Plasma Cutter 50AMP CUT-50 Dual Voltage 110-220V Cutting Machine will be the best choice for you.

Forney Easy Weld 251 20 P Plasma Cutter is best for cutting rusted and painted metal and available at a fair price.

 

plasma cutter benefits

 

If you did not like any of these cutters then you can choose from

Best plasma cutter 2021